Making over plain cotton upholstery fabric requires nothing more than a household disinfectant and water. Working outside, and wearing protective eyewear and gloves, lay the desired yardage for your project flat on a sheet of plastic. In a measuring cup, mix together ½ cup bleach and ½ cup water. Use a plastic spoon to drib-ble the liquid all over the fabric. When you're satisfied with the pattern, let dry, then run the fabric through a regular cycle in your washer and dryer. Take it to a local upholsterer (we sent ours to tapemeasure
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
There are a few common types of degrees that most furniture design schools offer. Associate and bachelor’s degrees typically enable students to learn the fundamentals of furniture design, as well as advanced techniques. These types of degrees usually take students two or four years to complete. Students who are looking for a more in depth education or those who would like to focus on a specific aspect of furniture design may want to consider earning a Master’s degree in furniture design.
First, use a drill to make a 1/8-inch-wide hole halfway down into a new cork ($3.99 for 30; winemakingsuperstore.com). Next, twist off the top of a vintage trophy (typically a few bucks each at thrift shops and garage sales). Apply superglue to the underside of the trophy top's base and the screw that extends from it. Insert the screw into the cork and twist the pieces together until flush and a tight bond forms. Allow one hour of drying time before using your prize design.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Blogger Brittany Moser of darkroomanddearly.com made these Polaroid-inspired drink rests from color photos and square tiles (a steal at 15 cents apiece). First, trim a photo to 3 3/4"W x 3 1/4"H. Using a foam brush, spread Mod Podge on the back of the image; then position it on a tile, leaving a 1/4-inch border at the top and sides, and a 3/4-inch border at the bottom. Let dry for 30 minutes. Spread Mod Podge over the photo and exposed tile borders and let dry for one hour; repeat two to three more times. Spray with clear sealant and let dry for 24 hours. Finally, affix adhesive felt pads to the underside corners of your picture-perfect tiles.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
We’ve already done rope, and now we’re on to another rustic material we love: wood! It’s as basic of a material as clay and is constantly reinvented by DIYers, crafters, artists, hackers, and carpenters. To get inspired to create our own batch of cool wooden objects, we turned to our favorite fellow makers to see what projects they’ve come up with. Scroll down for our top DIY wood project picks. 

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Our customers tell us they value our large selection of over 24,000+ woodworking tools and supplies. We provide multiple ordering options, fast shipping and responsive and no-hassle customer service. Our expert staff is available to assist you in your woodworking tool and supply needs, so please contact us with any questions at 800-645-9292. If you are a pro woodworker, please call our Pro Hotline at 800-321-9841 to sign-up for our pro program.
×