Because of his years of professional woodworking, his knowledge is broad. As a long-time professional woodworker he has built countless examples of fine dovetailed casework and drawers, carved tables, delicate inlay, sculpted chairs and elegant turned post beds. You’ll benefit from both his vast knowledge of woodworking and his many years of teaching experience. He’s also written six woodworking books as well as numerous articles for Fine Woodworking magazine.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
“Going to the furniture making evening class was the highlight of my week (and I wasn't the only person on the course to say that!) Emma was really brilliant at sharing her knowledge and experience to help guide us all through the tricky process of hand-making furniture, and thanks to her we all managed to make something we were proud to take home”   -    Kay Parnell, Student.
Flip the towel right side down. To determine where to place the tabs, center a spatula atop one of the towel’s shorter ends, and use straight pins to mark the spatula’s width. Place a tab at each pinned point, slightly over- lapping the tabs with the top of the towel. Make sure that each tab’s closed side lines up with the pins and that the open sides face each other. Remove the pins, then topstitch both tabs in place. Repeat on the towel’s other short end. 

Steve Brown CF '90, Instructor in the Cabinet & Furniture Making program, recently published a great how-to article in Fine Woodworking. The classic cabriole leg is a solid design choice for period furniture makers, but even with just that leg style, choosing from a variety of foot styles to go with it can be daunting. Steve helps clarify the process with step-by-step instructions for laying out and carving three common feet for the cabriole leg: the pad, slipper, and trifid foot.
First, use a drill to make a 1/8-inch-wide hole halfway down into a new cork ($3.99 for 30; winemakingsuperstore.com). Next, twist off the top of a vintage trophy (typically a few bucks each at thrift shops and garage sales). Apply superglue to the underside of the trophy top's base and the screw that extends from it. Insert the screw into the cork and twist the pieces together until flush and a tight bond forms. Allow one hour of drying time before using your prize design.
Course Entry Points:  There is great value in moving through our series of courses with a cohesive cohort of peers and our goal is to support this by having published start dates for each session.  However, because the nature of the instruction is so individualized, MSF may make allowances for students who wish to enter mid-session.  For example, If a student wants to enter in week 3 of the 12-week session, we may allow their enrollment contingent on their willingness to work outside of structured class hours and receive individual tutoring.

Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.
This simple craft turns your tattered cardigans, shrunken V-necks, or the kids' castoffs into coasters that you can use time and time again. Wash 100% wool in hot water, then dry with an agitator like jeans. After three rounds, sweaters should feel taut and felt-like. Use a pencil and a large-mouthed glass to trace circles onto the fabric and then snip out a set.

I know I’ve been a little MIA but we’ve had a big project in the backyard, an overwhelming workload (which we planned on being MUCH less), and then decided to hire out for some help to haul away a huge amount of dirt.  Unfortunately, that ended up with the guy we hired stealing from us…..uggggh.  When will we ever learn to not be so trusting?!  Steve and I both have a problem with that……but when did being “too trusting” become such an extreme character flaw?!!  Sad.  Anyway, the whole situation is under investigation and there are some definite twists to the story that the crime-show-watcher in me would love to share with any other crime-show-watching enthusiasts out there. ;) Hopefully soon.


LuxuryHomeStuff.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, LuxuryHomeStuff.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Attending a furniture design school provides a student with an opportunity to discover their craft, learn and develop design methods and techniques, master technical advancements in areas such as sustainability, and ultimately determine the trajectory of their career. Hands on experience is a vital element of the learning process, as is comprehensive knowledge of materials and their properties. The graduate leaves school with a portfolio showcasing their unique talents and abilities.

TechShop is a playground for creativity. Part fabrication and prototyping studio, part hacker-space and part learning center, TechShop provides access to over $1 million worth of professional equipment and software. We offer comprehensive instruction and expert staff to ensure you have a safe, meaningful and rewarding experience. Most importantly, at TechShop you can explore the world of making in a collaborative and creative environment.


There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
These delightful little volumes (inspired by Heather Mann of dollarstorecrafts.com) throw the book at desktop clutter. To transform ordinary matchboxes into match-"book" containers, print all five dust-jacket images, sized to fit basic 300-count matchboxes, from www.countryliving.com/matchboxcovers. Cut out and adhere the covers and pages to your matchboxes using spray mount. Then fill 'em up with the items referenced on the spines, and shelve.
First, use a drill to make a 1/8-inch-wide hole halfway down into a new cork ($3.99 for 30; winemakingsuperstore.com). Next, twist off the top of a vintage trophy (typically a few bucks each at thrift shops and garage sales). Apply superglue to the underside of the trophy top's base and the screw that extends from it. Insert the screw into the cork and twist the pieces together until flush and a tight bond forms. Allow one hour of drying time before using your prize design.
Training Length & Times:  Each professional training session (Fall, Winter, Spring) is 12 weeks in length and may include students at the Basic, Intermediate, or Master level. Our entire program takes 9 months to complete and so we recommend that students enroll in 3 consecutive sessions in order to complete the full curriculum.  Students attend small-group lectures, receive individualized instruction, and complete specific projects that are designed for their experience level.  Class instruction is available Mondays-Fridays from 9:00am-4:30pm with a 1-hour break for lunch.  The shop remains available for independent student work from 4:30pm to at least 8:00pm on most days.  The school is closed on holidays and there is a break between sessions and over part of the summer.  See our current schedule for specific session dates.

Established in 1906, the College for Creative Studies is a small, private, fully-accredited institution of higher learning. Diversity and inclusion characterize the student body: undergraduates hail from 35 states and 24 countries; while the graduate population is comprised of 81% international enrollees from 8 countries. Located in Midtown Detroit, students enjoy the long-established, rich culture of the city. From the Detroit Film Theatre and the Detroit Institute of Arts; to the libraries, galleries and famous restaurants; both college and students can leverage the educational opportunities provided by the urban community.
Ben Hobbs has been building period reproduction furniture for nearly 30 years. After teaching high school math for 10 years, Ben's passion for early American furniture and architecture drew him into the shop in 1982. Since then, Ben has operated as a bespoke custom furniture maker reproducing fine early American pieces, focusing on Southern and local NC examples. After training all three of his sons to be accomplished furniture makers, Ben opened his shop doors in 1996 to train students in his woodworking school.
Look at the types of things you do each day…each week. What can you move around so that it’s a better fit for you? Can you suggest to your team that you schedule meetings for late morning if you can’t stand to be social first thing? Can you schedule detailed project work or highly creative tasks, like writing or designing when you are best able to focus? How about making sales calls or client meetings on days when you are the most social and leaving billing or reports until another time when you are able to close your door and do repetitive tasks.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
Blogger Brittany Moser of darkroomanddearly.com made these Polaroid-inspired drink rests from color photos and square tiles (a steal at 15 cents apiece). First, trim a photo to 3 3/4"W x 3 1/4"H. Using a foam brush, spread Mod Podge on the back of the image; then position it on a tile, leaving a 1/4-inch border at the top and sides, and a 3/4-inch border at the bottom. Let dry for 30 minutes. Spread Mod Podge over the photo and exposed tile borders and let dry for one hour; repeat two to three more times. Spray with clear sealant and let dry for 24 hours. Finally, affix adhesive felt pads to the underside corners of your picture-perfect tiles.
Blogger Brittany Moser of darkroomanddearly.com made these Polaroid-inspired drink rests from color photos and square tiles (a steal at 15 cents apiece). First, trim a photo to 3 3/4"W x 3 1/4"H. Using a foam brush, spread Mod Podge on the back of the image; then position it on a tile, leaving a 1/4-inch border at the top and sides, and a 3/4-inch border at the bottom. Let dry for 30 minutes. Spread Mod Podge over the photo and exposed tile borders and let dry for one hour; repeat two to three more times. Spray with clear sealant and let dry for 24 hours. Finally, affix adhesive felt pads to the underside corners of your picture-perfect tiles.
Blogger Brittany Moser of darkroomanddearly.com made these Polaroid-inspired drink rests from color photos and square tiles (a steal at 15 cents apiece). First, trim a photo to 3 3/4"W x 3 1/4"H. Using a foam brush, spread Mod Podge on the back of the image; then position it on a tile, leaving a 1/4-inch border at the top and sides, and a 3/4-inch border at the bottom. Let dry for 30 minutes. Spread Mod Podge over the photo and exposed tile borders and let dry for one hour; repeat two to three more times. Spray with clear sealant and let dry for 24 hours. Finally, affix adhesive felt pads to the underside corners of your picture-perfect tiles.
Carving a Fan for Your Next Piece of Furniture The Carved Fan in Furniture Carvings found on 18th furniture are sometimes an ostentatious display of vines and leaves which cover nearly every exposed surface of the chair or chest to which they’re applied. I’ve always had a greater appreciation for minimal amounts of carving that accentuate a furniture […]
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
teastore.com). To get the show on the road, freehand the tea bag, tag, and spoon designs, using our image as a guide, with Pebeo's Porcelaine fine-point marker ($4.82; dickblick.com). Don't worry if you make a mistake—the ink can be washed away for up to 72 hours. Allow at least 24 hours' drying time, then bake the items for 35 minutes in a 300°F oven. Let cool completely, and wash (the ink's dishwasher safe!) before brewing up a spot of Earl Grey.
Great instruction — Lonnie is a master woodworker and a master teacher as well as a published author, known for his many woodworking books and articles. Lonnie has been woodworking for more than thirty-five years and teaching for over twenty-five. In other words, Lonnie has a background of woodworking skills to teach from. He’s not simply a magazine editor or tool salesman that works wood occasionally and teaches a few days each year; he has made woodworking and teaching woodworking his full-time passion (take a look at Lonnie’s work).
The Austin School of Furniture & Design will soon offer comprehensive furniture immersive programs that range from an intensive week-long project build to full-time furniture maker programs. These comprehensive classes are intended for intermediate to advanced students and will require an application and interview process or ASFD instructor approval.
Woodworker’s Hardware is your one-stop online woodworker’s store for all of your woodworker's supplies.  Shop for everything you need to start and finish your woodworking projects.  Find a huge selection of hardware products including drawer slides, barn door hardware, lazy susans, kitchen cabinet hardware & accessories, and furniture hardware.  We stock thousands of door and cabinet hardware and accessories like knobs, pulls, and hooks for kitchens, bathrooms, and closets. As one of the leading online kitchen cabinet hardware suppliers, shop for soft-close ball bearing drawer slides from top-rated brands like KV and Blum. Check out our sales page for our best offers! Our fully stocked warehouse full of woodworker’s supplies ensures shipping in 24 business hours.
We offer great projects — Our projects are beautifully-proportioned, attractive designs that you’re sure to be proud of as you create heirloom furniture. In fact, many people say that we offer some of the best woodworking projects in the USA! Lonnie personally custom-designs each furniture project to combine classic good looks with time-tested mortise-and-tenon and dovetail joints. These joints are considered the hallmark of fine craftsmanship. Lonnie also designs each woodworking project to maximize your learning experience so that you take new home techniques and skills.
See the Light: Abundant windows and glass-paned doors allow sunlight to pour inside. The seamless transition between indoors and out makes the room appear larger. Open up a tight kitchen with floating shelves. While they won’t hide toasters and coffeemakers, they’re a sleek alternative to upper cabinetry, which often overwhelms a tiny space. | CoastalLiving.comSee the Light: Abund
Wanna make your own owl baskets in a hoot? How about other crafts using crochet? You don't have to worry about it being too difficult because of this list of fun & easy crochet patterns for beginners like you! Read on [https://diyprojects.com/17-amazing-crochet-patterns-for-be…/] or follow us on IG: http://instagram.com/diyprojectsdotcom for more fun DIY ideas. 😉
Thinking my orders were now correct, I went to install the slides, and found you had sent me an odd number of Left/Right Blum drawer clips (they are sold in pairs. I ordered pairs. You sent me 5 right and 3 left). I emailed Teresa, personally, and guess what? No reply. So I called, and someone told me Teresa had quit. This new person apologized and said she'd send me a Left clip the same day.
Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.
6.Change your lightbulbs. Nothing is more frustrating than light bulbs burning out, especially because replacing them is one of those things you put on the to-do list and immediately forget about. Take the time to replace all of those lights for a brighter, happier space. In your bedroom or den, try opting for lower wattage lights (between 20- and 50-watts) to create a cozier and more romantic ambience. Here is a great guide to lighting your home.
The remaining tuition payment ($7,000.00) and materials deposit ($300.00) is due 45 days before the start date. Any unused materials deposit will be returned at the end of the course. You may use the materials deposit to buy books, finish, wood, fasteners, and hardware. Due to credit card processing fees, we kindly ask that students make this portion of the tuition payments by personal check, money order, or bank check.

The mission of the Fine Woodworking Department is to provide our students with opportunities for growth and development that set the foundation for life-long learning, academic achievement, and career accomplishment. We do this through three quality educational programs; traditional woodworking, advanced woodworking technology and lutherie. We encourage a passion for learning, through creativity, a commitment to excellence, and dedication to our students, and the communities we serve.
Take just a few minutes to look back at how your days and weeks have been unfolding. What time of the day are you the most focused? Do you prefer to be more social at certain times of the day? Do you have difficulty concentrating after lunch or are you energized? Are there days when you can’t seem to sit still at your desk and others when you could work on the same project for hours?
The mission of the Fine Woodworking Department is to provide our students with opportunities for growth and development that set the foundation for life-long learning, academic achievement, and career accomplishment. We do this through three quality educational programs; traditional woodworking, advanced woodworking technology and lutherie. We encourage a passion for learning, through creativity, a commitment to excellence, and dedication to our students, and the communities we serve.
Offering over 3500 full-size Woodcraft Patterns & Woodworking Project Plans! We're celebrating our 30th year of designing unique & original wood projects that "Make Woodcrafting Fun"... Christmas Woodcraft Patterns, Halloween Wood Projects, Yard Shadow Patterns, Indoor and Outdoor Furniture Wood Plans and more! Whatever the wood project, we've got the shop-tested patterns and plans that will simplify your woodworking with full-size traceable patterns, step-by-step instructions, assembly diagrams, wood layouts, material lists and…..technical support! Just call (800) 946-3435 if you ever have a question on any Winfield wood project!
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
Woven throughout the course will be presentations on the history of furniture making, the evolution of furniture styles and a review of contemporary styles. We’ll also do demonstrations on some advanced techniques such as shaping and using curved forms, drawer making, carcass construction, steam-bending, lamination, inlay, chairmaking, veneering, marquetry, and some contemporary joinery techniques. 

Great instruction — Lonnie is a master woodworker and a master teacher as well as a published author, known for his many woodworking books and articles. Lonnie has been woodworking for more than thirty-five years and teaching for over twenty-five. In other words, Lonnie has a background of woodworking skills to teach from. He’s not simply a magazine editor or tool salesman that works wood occasionally and teaches a few days each year; he has made woodworking and teaching woodworking his full-time passion (take a look at Lonnie’s work).


Established in 1906, the College for Creative Studies is a small, private, fully-accredited institution of higher learning. Diversity and inclusion characterize the student body: undergraduates hail from 35 states and 24 countries; while the graduate population is comprised of 81% international enrollees from 8 countries. Located in Midtown Detroit, students enjoy the long-established, rich culture of the city. From the Detroit Film Theatre and the Detroit Institute of Arts; to the libraries, galleries and famous restaurants; both college and students can leverage the educational opportunities provided by the urban community.

Perfectly customizable for any home bar or kitchen, wooden coasters are incredibly easy to make and perfect for the beginner craftsman or craftswoman. All it really takes is some precise (or imprecise, depending on the style you wish to achieve) cuts, a little to a lot of sanding, a tiny bit of finish, and the optional design you want on the coaster.
Tualatin, OR — October 1, 2014 — SawStop, LLC, the world leader in table saw safety, is celebrating 10 years of designing and manufacturing the world’s safest table saws. To commemorate the anniversary, between October 1 and December 31, 2014, in the United States and Canada each customer who purchases a new Industrial Cabinet Saw will receive over $200 in free […]
Toy-making was a special occupation of the the School's former kindergarten program in its earliest decades. The training offered young, mostly poor children not only brand new toys but also a set of usable skills. Today, with support from Thos. Moser, NBSS reflects on this legacy with a limited edition of 10 "Little Folks" Rockers lovingly handmade by School artisans. These charming collectors' items will benefit the Toys for Tots program, bringing joy and new toys to less fortunate children at Christmas.
×