Flip the towel right side down. To determine where to place the tabs, center a spatula atop one of the towel’s shorter ends, and use straight pins to mark the spatula’s width. Place a tab at each pinned point, slightly over- lapping the tabs with the top of the towel. Make sure that each tab’s closed side lines up with the pins and that the open sides face each other. Remove the pins, then topstitch both tabs in place. Repeat on the towel’s other short end.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.

How often do you go to close a cabinet door or drawer and it slams shut, making a seriously loud noise and throwing the contents of the cabinet or drawer all about? If you're like the millions of people without soft-close hinges, then it probably happens more often than you'd like it to. Not to mention, the hip-bump technique to close a cabinet drawer usually results in a loud bang and that's like your go-to move. Luckily for you and everyone else who hates it when their cabinets slam shut, it's relatively easy to install soft-close hinges or dampers. But before you decide yes or no, take a minute to look over the benefits of installing some soft-close hardware for cabinets.

We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
3.Rearrange the bookshelf. Reorganizing the bookshelf will easily make an entire room look more styled and polished, and you don't even have to get rid of anything. One tip is to arrange your books so they look like a smooth landscape of rolling hills. Put the tallest in the middle and fan out to the smallest or create multiple peaks (as long as the books flow together) or lay a few books on their side and stack them like a pyramid. For seven more tips to a visually organized bookshelf, click here.
Hi there, I'm glad that you are here. Firstly, let me introduce you that my name is Kevin Smith and I'm a coffee addicted guy, a blogger. Secondly, the reason why I create this website is to analyze what's the best products on the market with high quality and affordable price so that I make a decision to buy the right products for my family, friends and me. Thirdly, I just want to learn more about Home & Improvement Tools and Appliances so that I could improve my sweet little home.
Cut six strips of fabric from one towel. Two, measuring 33⁄4"W x 141⁄4"L each, will serve as the decorative horizontal bands at the top of the tote and should incorporate the towel’s graphics (as shown, left). The other four, measuring 31⁄2"W x 8"L, will form tabs for the bag’s handles. Turn under the long sides of each strip and press a 1⁄4" hem.
Schools that offer furniture design degrees are often necessary for learning the ins and outs of the furniture industry. This special area of industrial design is sometimes considered to be a mixture of several different industries, including interior design, fashion, and architecture. A good furniture design school will usually incorporate all of these elements into their furniture design programs.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?

We have a great location — Our woodworking school is located near Knoxville, Tennessee. We are very accessible (within a day’s drive of 70% of the population in the USA!) for USA woodworkers. While many of our woodworkers come from Southeastern USA locations such as Atlanta, we also have woodworkers who come from further-away places such as Texas, California, Oregon, Washington, Montana, Wyoming, Minnesota, Maine — 43 states so far and counting!  We’ve even had woodworkers come from other countries  — as far away as Australia! Additionally, our location near the Great Smoky Mountains and Gatlingburg ensures that there is an abundance of fantastic activities for you or your family to experience as well.

There are a few common types of degrees that most furniture design schools offer. Associate and bachelor’s degrees typically enable students to learn the fundamentals of furniture design, as well as advanced techniques. These types of degrees usually take students two or four years to complete. Students who are looking for a more in depth education or those who would like to focus on a specific aspect of furniture design may want to consider earning a Master’s degree in furniture design.


Perfectly customizable for any home bar or kitchen, wooden coasters are incredibly easy to make and perfect for the beginner craftsman or craftswoman. All it really takes is some precise (or imprecise, depending on the style you wish to achieve) cuts, a little to a lot of sanding, a tiny bit of finish, and the optional design you want on the coaster. 

But they had to start somewhere too right. If you’re looking to get into it, here some simple woodworking ideas that can get you started. There are a lot of cool projects about some easy wood ideas from wooden desks, shelves wooden clamps, trays and decorative articles to coffee table plans, rocking chairs wine holders, clocks, fences, wall designs, bird houses, cutlery, coasters and what not, that you can try as beginners and they tell you how to do it step by step.
Part-time classes at ASFD are geared toward dedicated hobbyists and aspiring furniture makers. They are held evenings and weekends to cater to students’ full-time work schedules. Part-time classes may cover a range of topics, skills, and projects. Classes will vary in duration, skill-level, and styles. As the school grows, so to do the classes. Large comprehensive and project-based classes are now being offered.
We all know people who ignore all of this advice and yet seem to prosper and achieve wonderful success anyway, but they are usually the exception, not the rule. For most of us, this habitual tendency to force our bodies and our brains into patterns of working that undermine our productivity result in achieving less than desired results and adding more stress to our already overburdened lives.
Carving a Fan for Your Next Piece of Furniture The Carved Fan in Furniture Carvings found on 18th furniture are sometimes an ostentatious display of vines and leaves which cover nearly every exposed surface of the chair or chest to which they’re applied. I’ve always had a greater appreciation for minimal amounts of carving that accentuate a furniture […]
Look at the bigger picture. Consider what happens during different months or times during the year. Think about what is going on in the other parts of your life. When is the best time for you to take on a new project, role or responsibility? Take into account other commitments that zap your energy. Do you have a sick parent, a spouse who travels all the time or young children who demand all of your available time and energy? 
×